Toyota Yaris Cross: svelata la nuova B-SUV giapponese

https%3A%2F%2Fmedia.autoblog.it%2F2%2F2d8%2Ftoyota_new_yaris_cross_front-left.jpg


Dopo lo slittamento della presentazione ufficiale al Salone di Ginevra, cancellato per il Coronavirus, Toyota ha svelato stamattina la nuova B-SUV della famiglia. Basata sulla nuova generazione dell’utilitaria di segmento B di Toyota, prende il nome di Yaris Cross.

Le dimensioni della Toyota Yaris Cross

La nuova Toyota Yaris Cross si basa sulla piattaforma TNGA (Toyota New Global Architecture) e si posizionerà sul mercato come sorella minore della C-HR. Misura 4.180 mm in lunghezza (240 mm più lunga della Yaris), 1.765 mm in larghezza, 1.560 mm in altezza, con una distanza tra gli assi di 2.560 cm. Sempre rispetto alla Yaris berlina, la Cross presenta sbalzi allungati: 6 cm l’anteriore e 18 cm il posteriore. Per il resto è 9 cm più alta e 2 cm più larga, mentre l’altezza da terra aumenta di 3 cm. La Casa giapponese non ha al momento dichiarato la capacità di carico del bagagliaio, ma ha annunciato un abitacolo modulabile con un sedile posteriore reclinabile con schema 40:20:40.












Toyota Yaris Cross: solo ibrida con la quarta generazione del sistema Toyota Hybrid

Sotto sul cofano della Toyota Yaris Cross trova posto la quarta generazione del sistema Toyota Hybrid, che deriva direttamente dal powertrain utilizzato già da altri modelli del marchio, come la Corolla o la RAV-4. Nel caso della Yaris Cross, e come sulla Yaris 2020, il motore termico impiegato è il 3 cilindri 1.5L a ciclo Atkinson abbinato a un motore elettrico da 59 KW, per una potenza complessiva di 116 CV. Secondo quanto dichiarato da Toyota l’efficienza termica di questo propulsore raggiungerebbe il 40%, il che permetterebbe di ridurre notevolmente i consumi e le emissioni di CO2 che, secondo il ciclo WLTP sarebbero inferiori ai 120 g/km per le versioni a trazione anteriore e sotto i 135 g per km per le varianti a trazione integrale AWD-i.




La nuova Yaris Cross sarà anche a trazione integrale

Per quanto riguarda un aspetto dinamico, le versioni della Toyota Yaris Cross dotate del sistema AWD-i sfrutteranno le quattro ruote motrici, senza però alcuna connessione fisica tra i due assi, grazie proprio al sistema ibrido. Di fatto la coppia viene trasmessa all’asse posteriore in partenza e in accelerazione (o nei casi di perdita di aderenza), per il resto il sistema funziona come una trazione anteriore tradizionale.

Sicurezza: ultima generazione del Toyota Safety Sense




E infine la sicurezza. La nuova Toyota Yaris Cross sarà dotata dell’ultima evoluzione del pacchetto Toyota Safety Sense, per questo potrà godere dei sistemi di ultima generazione come il cruise control adattivo e il mantenimento automatico della corsia.

La nuova Toyota Yaris Cross sarà prodotta in Francia con un volume di 150.000 unità all'anno e arriverà sui mercati nel 2021.

14 Guarda la Galleria "Toyota Yaris Cross 2020"

Toyota Yaris Cross: svelata la nuova B-SUV giapponese pubblicato su Autoblog.it 23 aprile 2020 11:04.

Leggi Tutto...
 
FULL AND QUALITATIVE DIAGNOSTICS OF ENGINE AND OTHER CAR SYSTEMS DO NOT BE ELM327 AT ALL WISHES OF THE OWNER ... DO NOT NEED TO FEED ILLUSIONS ... It’s important to use the ELM-327 engine somewhere, if you don’t have to go to the panel, “God forbid,” the machine will start to work "not normal" in order to at least understand what kind of repair to start preparing for ... independently decrypting the errors ...

Recently, in various kinds of automotive forums, there has been, to one degree or another, interest in diagnosing a car using the ELM-327 adapter. I decided to share information on connectivity, settings, etc.

This adapter allows you to view the following parameters:
• Engine turns;
• Coolant temperature;
• Short-term fuel correction;
• Long-term fuel correction;
• Pressure in the intake manifold;
• Oxygen sensor data;
• Engine turns;
• engine load;
• State of the fuel system;
• Vehicle speed;
• Absolute air pressure;
• Advance ignition;
• Intake air temperature;
• Mass air flow;
• Throttle position;
• Graphic display of the parameters of the above parameters;
Supported ELM327 adapter protocols:
• ISO15765-4 (CAN bus): Audi, Opel, VW, Ford, Jaguar, Renault, Peugeot, Chrysler, Porsche, Volvo, Saab, Mazda, Mitsubishi;
• ISO14230-4 (KWP2000): Daewoo, Hyundai, KIA;
• ISO9141-2: Honda, Infinity, Lexus, Nissan, Toyota, Audi, BMW, Mercedes, Porsche;
• J1850 VPW: Buick, Cadillac, Chevrolet, Chrysler, Dodge, GM, Isuzu;
• J1850 PWM: Ford, Lincoln, Mazda

Diagnostic software ELM-327 is full on torrents, Google Play, and indeed on the Internet.
For example, a good selection of Carzis diagnostic program.

ELM-327 connection settings:

ELM 327 Bluetooth Connection:
Attention! In order to avoid power surges that could damage the adapter and / or the car's computer, we recommend that you connect / disconnect the scanner only when the ignition is off.
1. Install any ELM 327 program on your device;
2. Connect the ELM327 Bluetooth to the ODB 2 diagnostic connector of your car;
3. Turn on the ignition or start the car;
4. Go to the settings of your Android device;
5. Go to the wireless settings;
6. Turn on Bluetooth and click "Bluetooth Settings";
7. Click "Search for devices";
8. Select the found Elm327 adapter with the name "OBD-II";
9. Enter the pairing code elm327: 1234
10. If the code approached, you will see the inscription "Paired, but not connected." This completes the setup. In very rare cases, the pairing code can be 0000 or 6789;
11. Run the previously installed program;
12. After starting the program, you will see that the only device on the main screen of the program is INACTIVE;
13. Press "Menu" and go to "Settings". In the settings, select "OBD2 adapter settings";
14. Click "Connection Type";
15. Select "Bluetooth";
16. Click "Select a Bluetooth device";
17. Select the device with which you paired in step 8. This completes the program setup. Return to the main screen of the program;
18. Take full advantage of the Elm327 adapter!

ELM 327 WI-FI connection (smartphones on IOS work only via WIFI):
Attention! In order to avoid power surges that could damage the adapter and / or the car's computer, we recommend that you connect / disconnect the scanner only when the ignition is off.
1. Install any ELM 327 program on your device;
2. Connect the ELM327 Wi-Fi car diagnostic adapter to the OBD II connector of the diagnosed vehicle;
3. Insert the key into the ignition switch and turn on the car ignition (can be wound up);
4. Go to the Wi-Fi wireless settings section of your phone / tablet / computer .;
5. Select a WiFiOBD network. Go to settings, on the tab "Static";
6. In this tab, enter the following data:
IP Address: 192.168.0.38
Subnet Mask: 255.255.255.0
Main Gateway: 192.168.0.10
Port: 35000
HTTP Proxy: Auto
7. Go to the program menu that you installed in the first paragraph on the phone / tablet to work with the adapter;
8. Pair the program with the vehicle ECU. Done!
 
Indietro
Alto